Comparison ledger
Lapmaster 15 Lapper, Ontrak DSS 200 Series II Post, side by side. Every value shown is drawn from the cited encyclopedia entries.
| Attribute | 15 LapperLapmaster | DSS 200 Series II PostOntrak |
|---|---|---|
| OEM | Lapmaster | Ontrak |
| Category | CMP | CMP |
| Wafer size | — | — |
| Process node | — | — |
| Introduced | — | 2023 |
| Production run | — | — |
| Lifecycle | — | — |
| Lifecycle milestones | — | — |
| Control system | — | — |
| Generation | — | — |
| Family | Lapmaster 15 | Ontrak DSS 200 |
| Specifications | ||
| Number Of Conditioning Rings | Up to 3[1] | — |
| Ring ID | Up to 5.5″[1] | — |
| Plate Diameter – Outside | 15″[1] | — |
| Plate Diameter – Inside | 3 1/2″[1] | — |
| Standard RPM | 60[1] | — |
| Drive Motor | 1/2 HP[1] | — |
| Electrics | 110V / 1Ph / 60Hz[1] | — |
| Dimensions – Approximate | 26″(L-R) x 21″(F-B) x 22″(H)[1] | — |
| Configuration | Equipped with:[1] | 50/60 Hz[2] |
| Equipped with: 15″ Cast Iron Plate | Included[1] | — |
| Equipped with: (3) Yoke/Roller Bearing Assemblies | Included[1] | — |
| Equipped with: (3) Conditioning Rings | Included[1] | — |
| Equipped with: (3) Hold Downs | Included[1] | — |
| Equipped with: 30 Minute Timer | Included[1] | — |
| Voltage | — | 200/ 208 / 220 VAC[2] |
| Breaker | — | 25 A (5.2 kW)[2] |
| Total FLA | — | 6.8 A (1.4 kW)[2] |
| Largest Load | — | 3.6 A (0.8kW)[2] |
| CDA (Clean Dry Air) | — | 80-100 PSI (Inlet)[2] |
| DI Water | — | 60-80 PSI (Inlet)[2] |
| Process Solutions / Chems | — | 15 PSI (Inlet)[2] |
| Drain | — | 132 GpH Peak, 60 GpH Idle, 2" CPVC[2] |
| Noise Level | — | 70 dB (during process)[2] |
| Total FL | — | 6.8 A (1.4 kW)[3] |
| Largest load | — | 3,6A (0,8kW)[4] |
| Process solutions/chems | — | 15PSI (Inlet), 1/4" OD Teflon tubing[4] |
| Wafer Sizes | — | 8 inch[2] |
| CDA (Clean Dry Air) Inlet | — | 80-100 PSI, 3/8" OD Tubing[2] |
| DI Water Inlet | — | 60-80 PSI, 3/4" OD Teflon Tubing[2] |
| Process Solutions / Chems Inlet | — | 15 PSI, 1/4" OD Teflon Tubing[2] |
| Wafer Size | — | 8 inch[2] |
| CDA Inlet Pressure | — | 80-100 PSI[2] |
| CDA Tubing | — | 3/8" OD[2] |
| DI Water Inlet Pressure | — | 60-80 PSI[2] |
| DI Water Tubing | — | 3/4" OD Teflon[2] |
| Process Solutions / Chems Pressure | — | 15 PSI[2] |
| Process Solutions / Chems Tubing | — | 1/4" OD Teflon[2] |
| Drain Flow (Peak) | — | 132 GpH[2] |
| Drain Flow (Idle) | — | 60 GpH[2] |
| Drain Pipe Size | — | 2" CPVC[2] |
| Noise Level (during process) | — | 70 dB[2] |